TI CC1312R IntroduceIssuing time:2022-11-07 16:01 TI CC1312R IntroduceCC1312R Features•Microcontroller – Powerful 48-MHz Arm® Cortex®-M4F processor – EEMBC CoreMark® score: 148 – 352KB of in-system programmable flash – 256KB of ROM for protocols and library functions – 8KB of cache SRAM (alternatively available as general-purpose RAM) – 80KB of ultra-low leakage SRAM. The SRAM is protected by parity toensure high reliability of operation. – 2-pin cJTAG and JTAG debugging – Supports over-the-air (OTA)update •Ultra-low power sensor controller with 4KB of SRAM – Sample, store, and process sensor data – Operation independent from system CPU – Fast wake-up for low-power operation •TI-RTOS, drivers, bootloader, and IEEE 802.15.4 MAC in ROM for optimizedapplication size •RoHS-compliant package – 7-mm × 7-mm RGZ VQFN48 (30 GPIOs) •Peripherals – Digital peripherals can be routed to any GPIO – 4× 32-bit or 8× 16-bit general-purpose timers – 12-bit ADC, 200 kSamples/s, 8 channels – 2× comparators with internal reference DAC (1× continuous time, 1×ultra-low power) – Programmable current source – 2× UART – 2× SSI (SPI, MICROWIRE, TI) – I2C – I2S – Real-time clock (RTC) – AES 128- and 256-bit cryptographic accelerator – ECC and RSA public key hardware accelerator – SHA2 accelerator (full suite up to SHA-512) – True random number generator (TRNG) – Capacitive sensing, up to 8 channels – Integrated temperature and battery monitor • Externalsystem – On-chip buck DC/DC converter – TCXO support • Lowpower – Wide supply voltage range: 1.8 V to 3.8 V – Active mode RX: 5.8 mA (3.6 V, 868 MHz) – Active mode TX at +14 dBm: 24.9 mA (868 MHz) – Active mode MCU 48 MHz (CoreMark): 2.9 mA (60 μA/MHz) – Sensor controller, low power-mode, 2 MHz, running infinite loop:30.1 μA – Sensor controller, active mode, 24 MHz, running infinite loop: 808μA – Standby: 0.85 µA (RTC on, 80KB RAM and CPU retention) – Shutdown: 150 nA (wakeup on external events) • Radiosection – Flexible high-performance sub-1 GHz RF transceiver – Excellent receiver sensitivity: -121 dBm for SimpleLink long-rangemode -110 dBm at 50 kbps – The Maximum air data rate: 4000 kbps – Output power up to +14 dBm with temperature compensation – Suitable for systems targeting compliance with worldwide radiofrequency regulations • ETSIEN 300 220 Receiver Category 1.5 and 2, EN 303 131, EN 303 204 (Europe) • FCC CFR47 Part 15 • ARIBSTD-T108 – Wide standard support •Wireless protocols – IEEE 802.15.4g, IPv6-enabled smart objects (6LoWPAN), MIOTY®,Wireless M-Bus, WiSUN®, KNX RF, Amazon Sidewalk, proprietary systems,SimpleLink™ TI 15.4 stack (Sub-1 GHz), and dynamic multiprotocol manager (DMM)driver. •Development Tools and Software – CC1312R LaunchPad™ Development Kit – SimpleLink™ CC13x2 and CC26x2 Software Development Kit (SDK) – SmartRF™ Studio for simple radio configuration – Sensor Controller Studio for building low-power sensingapplications CC1312R Applications• 169,433, 470 to 510, 868, and 902 to 928 MHz ISM and SRD systems 1 with down to 4kHz of receive bandwidth •Building automation – Building security systems – motion detector, electronic smart lock, door and window sensor,garage door system, gateway – HVAC – thermostat, wireless environmental sensor, HVAC system controller,gateway – Fire safety system – smoke and heat detector, fire alarm control panel (FACP) – Video surveillance – IP network camera – Elevators and escalators – elevator main control panel for elevators and escalators • Gridinfrastructure – Smart meters – water meter, gas meter, electricity meter, and heat costallocators – Grid communications – wireless communications – Long-range sensor applications – Other alternative energy – energy harvesting •Industrial transport – asset tracking •Factory automation and control •Medical •Electronic point of sale (EPOS) – Electronic Shelf Label (ESL) •Personal electronics – Connected peripherals – consumer wireless module – Home theater & entertainment – smart speakers, set-top box – Gaming – Wearables (non-medical) CC1312R DescriptionTheSimpleLink™ CC1312R device is a multiprotocol Sub-1 GHz wirelessmicrocontroller (MCU) supporting IEEE 802.15.4g, IPv6-enabled smart objects(6LoWPAN), MIOTY®, Wi-SUN®, proprietary systems, including the TI 15.4-Stack(Sub-1 GHz). The device is optimized for low-power wireless communication andadvanced sensing in building security systems, HVAC, smart meters, medical,wired networking, portable electronics, home theater & entertainment, andconnected peripherals markets. Thehighlighted features of this device include: •Flexible Sub-1 GHz radio supporting industry standard frequency bands (315 MHz,433 MHz, 868 MHz, 900 MHz, and more) to meet the industrial needs. • Wideflexibility of protocol stack support in the SimpleLink™ CC13x2 and CC26x2Software Development Kit (SDK) including complete SimpleLink™ 15.4-Stack (Sub-1GHz) solution. •Maximum transmit power of +14 dBm at Sub-1 GHz with 24.9 mA currentconsumption. • Longerbattery life wireless applications with low standby current of 0.85 µA and fullRAM retention. •Industrial temperature ready with lowest standby current of 11 µA at 105°C. •Advanced sensing with a programmable, autonomous ultra-low power SensorController CPU with fast wakeup capability. As an example, the sensorcontroller is capable of 1-Hz ADC sampling at 1 µA system current. • LowSER (Soft Error Rate) FIT (Failure-in-time) for long operation lifetime with nodisruption for industrial markets with always-on SRAM parity against corruptiondue to potential radiation events. •Dedicated software controlled radio controller (Arm® Cortex®-M0) providingflexible low-power RF transceiver capability to support multiple physicallayers and RF standards. •Excellent radio sensitivity (-121 dBm) and robustness (selectivity andblocking) performance for SimpleLink™ long-range mode.
Maximum transmit power of +14 dBm at Sub-1 GHz with 24.9 mA current consumption. The CC1312 UARTs implement universal asynchronous receiver and transmitter functions. They support flexible baudrate generation up to a maximum of 3 Mbps.
|