200 Milliwatts CC1314R10+PA FSK Radio Dongle

N538EP CC1314R10 FSK radio Dongle based TI CC1314R10 SUB GHz wireless mcu, PA and USB to uart chip, the FSK radio dongle designed for 169M, 433M, 868M, 915M and 1200Mhz band. It can be debug or program by customizer. The CC1314R10 wireless dongle has +24 dBm output power and the sensitivity down to -110 dBm at 50 kbps. The dongle support IEEE 802.15.4g, IPv6-enabled smart objects (6LoWPAN), MIOTY, Wireless M-Bus, Wi-

SUN, KNX RF, Amazon Sidewalk, proprietary systems, SimpleLink™ TI 15.4 stack (Sub-1 GHz), and dynamic multiprotocol manager (DMM) driver and so on.

The CC1314R10 Dongle has a small private USB shell, Integrated buttons and dual color LED 3528, CC1314R10, PA, cp2102 and pcb antenna, with the specialized custom shell, it reduced a lot of development troubles, Only the most software programming is needed to quickly push it to the market. Suitable for 802.15.4 edge gateways, sniffers, packet catchers, etc. The USB shell is compact and exquisite, suitable for personal or commercial use. Can be OEM/ODM. The length, width, and height of the shell are 45 x 19 x 8 mm. The color of the shell and buttons can be customized.

N538EP FSK radio dongle hardware is designed for maximum range, 2000m + Range (Low rate and Line of Sight).

The N538EP Private Shell By Coral RF

Master Chip CC1314R10 Features

• Powerful 48MHz Arm Cortex-M33 processor with TrustZone

• FPU and DSP extension

• 1024kB flash program memory

• 8kB of cache SRAM

• 256kB of ultra-low leakage SRAM with parity for high-reliability operation­32kB of additional SRAM if parity is disabled

• Dynamic multiprotocol manager (DMM) driver

• Supports over-the-air update (OTA)

N538EP cc1314R10 Dongle Wireless protocols

• Wi-SUN®

• mioty®

• Amazon Sidewalk

• Wireless M-Bus

• SimpleLink™ TI 15.4-stack

• Proprietary systems

N538EP cc1314R10 Dongle radio performance

• -110dBm sensitivity at 50kbps

• up to 24dBm output power at 5V

N538EP cc1314R10 Dongle UART baud

• UART baud up to 3Mbps.

N538EP cc1314R10 Dongle Parameters

How to used N538EP Dongle ?

1. N538EP dongle KEY, LED, DEBUG, SWITCH port circult

1) N538EP dongle KEY circult

2) N538EP dongle LED circult

3) N538EP dongle Debug Port

Note: for XDS110V3, only TCK and TMS used. For jtag, please view the guider of CC1314.

4) N538EP dongle UART port

    DIO3-->TXD;    DIO2<--RXD;

5) PA LOGIC circult

2. RF test

step 1:

connect N538EP to XDS110

step 2:

1) Open smart RF studio 7,

2) Open cc1314R10 interface,

3) SET PA IO

Then you can proceed with RF testing.

3. UART test

step 1:

Download the fireware to N538EP cc1314R10 Dongle

step 2:

install CP2102 driver in your computer,secect VCP port.

step 3:

send the data from putty to VCP port, then can receive the same data from N538EP from dongle.

N538EP cc1314R10 Dongle Download

CC1314R10 datasheet‍‍‍     

N7538EP datasheet

CP2102 DRIVER‍