20 Milliwatts CC1311 FSK Radio Dongle

N534DP CC1311 FSK radio Dongle based TI CC1311R3 SUB GHz wireless mcu, and USB to uart chip, the FSK radio dongle designed for 169M, 433M, 868M, 915M and 1200Mhz band. It can be debug or program by customizer. The CC1311 wireless dongle has +14 dBm output power and the sensitivity down to -110 dBm at 50 kbps. The dongle support IEEE 802.15.4g, IPv6-enabled smart objects (6LoWPAN), MIOTY, Wireless M-Bus, Wi-

SUN, KNX RF, Amazon Sidewalk, proprietary systems, SimpleLink™ TI 15.4 stack (Sub-1 GHz), and dynamic multiprotocol manager (DMM) driver and so on.

The CC1311 Dongle has a small private USB shell, Integrated buttons and dual color LED 3528, CC1311R3, cp2102 and pcb antenna, with the specialized custom shell, it reduced a lot of development troubles, Only the most software programming is needed to quickly push it to the market. Suitable for 802.15.4 edge gateways, sniffers, packet catchers, etc. The USB shell is compact and exquisite, suitable for personal or commercial use. Can be OEM/ODM. The length, width, and height of the shell are 45 x 19 x 8 mm. The color of the shell and buttons can be customized.

N534DP FSK radio dongle hardware is designed for maximum range, 1000m + Range (Low rate and Line of Sight).

The N534DP Private Shell By Coral RF

N534DP Master Chip CC1311R3 Features

• Powerful 48MHz Arm Cortex-M33 processor with TrustZone

• FPU and DSP extension

• 352kB flash program memory

• 8kB of cache SRAM

• 80kB of ultra-low leakage SRAM with parity for high-reliability operation­32kB of additional SRAM if parity is disabled

• Dynamic multiprotocol manager (DMM) driver

• Supports over-the-air update (OTA)

N534DP cc1311R3 Dongle Wireless protocols

• Wi-SUN®

• mioty®

• Amazon Sidewalk

• Wireless M-Bus

• SimpleLink™ TI 15.4-stack

• Proprietary systems

N534DP cc1311R3 Dongle radio performance

• -110dBm sensitivity at 50kbps

• up to 14dBm output power at 5V

N534DP cc1311R3 Dongle UART baud

• UART baud up to 3Mbps.

N534DP cc1311R3 Dongle Parameters

How to used N534DP cc1311R3 Dongle ?

1. N534DP cc1311 dongle KEY, LED, DEBUG port circult

1) N534DP dongle KEY circult

2) N534DP dongle LED circult

3) N534DP dongle Debug Port

Note: for XDS110V3, only TCK and TMS used. For jtag, please view the guider of CC1311.

4) N534DP dongle UART port

    DIO3-->TXD;    DIO2<--RXD;

2. N534DP cc1311 Dongle RF test

step 1:

connect N534DP to XDS110

step 2:

1) Open smart RF studio 7,

2) Open cc1311R3 interface,

Then you can proceed with RF testing.

3. N534DP cc1311R3 Dongle UART test

step 1:

Download the fireware to N534DP cc1311R3 Dongle

step 2:

install CP2102 driver in your computer,secect VCP port.

step 3:

send the data from putty to VCP port, then can receive the same data from N534DP from dongle.

N534DP cc1311R3 Dongle Download

CC1311R3 datasheet

N7534DP datasheet

CP2102 DRIVER‍