N533KS high power radio module based TI CC1311P3, PA and LNA.
N533KS integrated TI CC1311P3 transceiver, high power PA and LNA chip, suitable for 169M, 433M, 868MHz, 915M and 1200MHz band. AT command support.
N533KS high power module output power is +33 dBm. CC1311P3 transceiver module has the characteristics of low cost, low power consumption and small size. The transceiver module is designed with 4-layer board, with excellent impedance matching and anti-interference. The module is mainly for IoT, intelligent home, wireless meter reading, scientific research and medical treatment, and medium and long-distance wireless communication equipment. N533KS leads all pins of CC1311P3 out for secondary development.
ISM Frequency supported by N533KShigh power module
150M band: 150 MHz to 160 MHz (China)
169M band: 160 MHz to 172 MHz (China)
433M band: 430 MHz to 440 MHz (China)
490M band: 470 MHz to 510 MHz (China)
770M band: 770 MHz to 780 MHz (China)
868M band: 868 MHz to 870 MHz (China, EU, USA)
888 MHz to 889 MHz (Australia)
915M band: 902 MHz to 928 MHz (USA)
1200M band: 1100 MHz to 1250 MHz (USA)
CC1311PS high power module up to +33 dBm outpower and down to -112 dBm sensitivity.
N533KShigh power module (CC1311P3) is suitable for free frequency band in China.
RF Interface | Parameter | Introduce |
Frequency | 150M, 433M, 868MHz, 915M, 1200MHz | Support ISM |
Output Power | +33 dBm | The maximum power 2000mW |
Sensitivity | -112 dBm | 50kbps |
Symbol Rate | 0.3-2000 kbps | Software programming control |
Deviation | +/-10 kHz | Antenna interface |
Distance | 14000 m | In clear and open environment, the antenna gain is 3 dBi, the height above the ground is 2.5 meters, and the air speed is 1.2 kbps. |
Hardware parameters | Value | Remarks |
Size | 36 x 22 x 3 mm | - |
Antenna Interface | IPEX, stamp hole | - |
Communication Interface | UART, SPI | Software programming |
Package | SMD | - |
Electrical Parameters | Minimum | Typical | Maximum | Remarks |
Volt | 1.8V | 3.3V | 3.9V |
|
PA Volt | 3V | 5V | 6V |
|
Emission Current |
| 1500mA |
| Instantaneous power consumption |
Receiving Current |
| 12mA |
| - |
Sleep current |
| 1uA |
| Software programming control |
Working Temperature | -30℃ |
| 75℃ | - |
N533KS Datasheet download
Ordering information
N533KS-150M CC1311P3 +PA +LNA +33 dBm, 150Mhz-160Mhz
N533KS-169M CC1311P3 +PA +LNA +33 dBm, 160Mhz-175Mhz
N533KS-433M CC1311P3 +PA +LNA +33 dBm, 410Mhz-440Mhz
N533KS-470M CC1311P3 +PA +LNA +33 dBm, 470Mhz-510Mhz
N533KS-770M CC1311P3 +PA +LNA +33 dBm, 770Mhz-780Mhz
N533KS-868M CC1311P3 +PA +LNA +33 dBm, 860Mhz-880Mhz
N533KS-915M CC1311P3 +PA +LNA +33 dBm, 910Mhz-930Mhz
N533KS-1200M CC1311P3 +PA +LNA +33 dBm, 1100Mhz-1250Mhz
Test method of N533KS module
Take the supporting base plate of Heyan technology as an example:
The bottom board of N533KS is T532AP, which integrates USB to serial chip, led, button, burning port and module card port. As shown in the figure:
N533KS secondary development method:
The CC1311P3 module is stuck on the backplane as shown in the figure, and the IPEX is connected with the antenna. The burning port is connected with xds110 according to the silk screen printing, and then online simulation can be carried out to test the performance of the module.
Module Programming
The schematic diagram of the module base plate can be obtained from our official website.
Please contact us for specific programming information or download it from TI official website www.ti.com.
Files download
N533KS Software code example Download N533KS datasheet Download CC1311P3 datasheet
